KitchenAid KECD867XBL Manuel d'instructions télécharger pdf (Page 4)

Cabinet Dimensions

NOTES: After making the countertop cutout, some installations

may require notching down the base cabinet side walls to clear

the cooktop base. To avoid this modification, use a base cabinet

with sidewalls wider than the cutout.

■ A minimum side clearance of 6" (15.2 cm) is recommended

between side of cooktop and side wall for maximum

ventilation performance.

■ A minimum clearance of 2" (5.1 cm) is recommended

between the motor/blower and cabinet for proper cooling. A

6" (15.2 cm) clearance is recommended for servicing access.

Cutout Dimensions

Venting Requirements

IMPORTANT: This cooktop must be exhausted outdoors.

■ Do not terminate the vent system in an attic or other enclosed

area.

■ Use a vent cap.

■ Vent system must terminate to the outside.

■ Use only a 6" (15.2 cm) diameter round or 3¼" x 10"

(8.3 x 25.4 cm) rectangular vent except as follows: For

electric cooktops, a 5" (12.7 cm) diameter round vent may be

used for venting straight out the back of the cooktop and

directly through the wall for 10 ft (3.0 m) or less.

■ Before making cutouts, make sure there is proper clearance

within the wall or floor for the exhaust vent.

■ Do not cut a joist or stud unless absolutely necessary. If a

joist or stud must be cut, then a supporting frame must be

constructed.

■ The size of the vent should be uniform.

■ The vent system must have a damper. If roof or wall cap has a

damper, do not use damper supplied with the range hood.

■ Use vent clamps to seal all joints in the vent system.

■ Use caulking to seal exterior wall or roof opening around the

cap.

■ Determine which venting method is best for your application.

A. 30" (76.2 cm) on 30" (76.2 cm) models

36" (91.4 cm) on 36" (91.4 cm) models

B. Combustible area above countertop (shown by dashed box above)

C. 30" (76.2 cm) minimum clearance between top of cooktop platform

and bottom of uncovered wood or metal cabinet (24" [61 cm]

minimum clearance if bottom of wood or metal cabinet is covered

by not less than ¹⁄₄" [0.6 cm] flame retardant millboard covered with

not less than No. 28 MSG sheet steel, 0.015" [0.04 cm] stainless

steel, or 0.024" [0.06 cm] aluminum or 0.020" [0.05 cm] copper)

D. 13" (33 cm) recommended upper cabinet depth

E. 2" (5.1 cm)

F. 2 1 ¹⁄₈" (53.7 cm)

G. 18" (45.7 cm) minimum clearance from upper cabinet to countertop

within minimum horizontal clearances to cooktop

H. Junction box or outlet; 12" (30.5 cm) minimum from bottom of

countertop

I. Junction box or outlet; 10" (25.4 cm) from right-hand side of

cabinet

J. 28⁷⁄₈" (73.3 cm) on 30" (76.2 cm) models

34⁹⁄₁₆" (87.8 cm) on 36" (91.4 cm) models

K. 2½" (6.4 cm) minimum distance to nearest left and right side

combustible surface above cooktop

L. 1½" (3.8 cm) minimum clearance between back wall and

countertop

A. 28⁷⁄₈" (73.3 cm) maximum on 30" (76.2 cm) models

34⁹⁄₁₆" (87.8 cm) maximum on 36" (91.4 cm) models

B. 21¹⁄₈" (53.7 cm) maximum on both 30" (76.2 cm) and 36" (91.4 cm)

models

C. 8¹⁹⁄₃₂" (21.8 cm) on 30" (76.2 cm) models

15⁷⁄₁₆" (39.2 cm) on 36" (91.4 cm) models

D. 6¹⁹⁄₆₄" (16.0 cm) on both 30" (76.2 cm) and 36" (91.4 cm) models

E. 2" (5.1 cm) minimum space to front edge of cooktop

F. Floor exhaust option

G. 6¹⁄₈" (15.6 cm) for 6" (15.2 cm) vent system

5¹⁄₈" (13 cm) for 5" (12.7 cm) vent system

H. 8¹⁹⁄₃₂" (21.8 cm) on 30" (76.2 cm) models

15⁷⁄₁₆" (39.2 cm) on 36" (91.4 cm) models

I. 16" (40.6 cm) on both 30" (76.2 cm) and 36" (91.4 cm) models

J. Wall exhaust option

1 2 3 4 5 6 7 8 9 ... 19 20

Commentaires sur ces manuels

Pas de commentaire

KitchenAid KECD867XBL Manuel d'instructions Page 4

Commentaires sur ces manuels